减速机一些保养的方法和检修方法

2015-08-05 17:51:21 hmico

减速机的日常维护相当重要，现在美科机械给大家关于减速机一些保养的方法和检修方法：
Guomao reducer to you on the reducer some maintenance and repair method method:
国茂减速机保养最重要的就是必须定期换油，检查声音大小，是否有异常。一般大攻略的减速机需要油泵润滑。若空载低速启动，等到运行平稳后再进行加载。
The most important is the maintenance of Guomao reducer must be regular oil, check whether there is abnormal sound. General introduction of the reducer need to pump lubrication. If no load at low speed start, until after running smoothly and then load.
轴承与轴、轴与蜗轮的配合面压入前应涂润滑油。国茂减速机一般的检修方法分为如下几个方面：
Bearing and shaft, shaft and worm gear in front of the mating surface should be coated with lubricating oil. The maintenance method of Guomao reducer in general is divided into the following several aspects:
1、拆卸润滑系统是指拆卸蜗轮锁紧螺母，使用专用工具卸蜗轮，并检查蜗轮与蜗杆啮合情况，包括接触面积、位置、磨损情况等。但是同时也要拆卸油封，清洗机箱，检查处理中间剖分面。
1, remove the lubrication system is to remove the worm gear lock nut, use special tool to unload the worm gear, and check the worm gear and worm gear meshing, including contact area, position, wear and so on. But at the same time also to remove the oil seal, cleaning the case, check the processing of the middle section.
2、拆卸蜗轮减速机主要包括拆卸皮带罩、三角皮带、皮带轮，拆卸联轴节、螺栓、吊下电动机。除此之外，还要拆卸蜗杆两端盖和减速器剖分面的螺栓，吊起机壳上盖放于橡胶板上，要防止中间剖分面损伤，并清洗上盖，检查紧固螺栓处是否漏油。
2, remove the worm gear reducer includes removing belt cover, triangle belt, belt wheel, removing coupling, bolts, hanging under the motor. In addition, but also removing worm at both ends of the cover and the reducer subdivision surface of the bolt, lift the upper cover of the casing. Put on the rubber plate, to prevent the intermediate subdivision surface damage, and cleaning cover, check the fastening bolt leaks.
3、轴颈磨损可采用喷涂、刷涂、电镀后磨削方法修复。轴上键槽损坏，可在离原键槽120°相位处重新加工键槽。
3, the shaft neck wear can be used to spray, brush, plating after the repair method. The shaft keyway damage, can be re processed from the original 120 degrees in the keyway keyway phase.
4、检查蜗轮、蜗杆，我认为主要是蜗轮磨损、点蚀、胶合（粘着撕伤）严重的，可更换或采用修正蜗轮的方法修复蜗轮、重新配制蜗杆。而蜗轮、蜗杆齿面轻度胶合、点蚀及个别齿面有缺陷，可采用补焊后铣削，刮削及研磨等方法修复。
4, check the worm gear, worm, I think the main is worm gear wear, pitting, glue (adhesive tear) serious, can be replaced or the use of modified worm gear method to repair the worm gear, worm. And the worm wheel and worm tooth surface slight scuffing, pitting and individual tooth surface defects, the repair welding after milling, scraping and grinding and other methods to repair.
5、减速机装配前对零件进行清洗，去毛刺，并按图样要求核对尺寸，几何形状、精度、表面粗糙度等。
5, the reducer assembly before cleaning the parts, to burr, and according to the requirements of the drawings to check the size, geometry, accuracy, surface roughness, etc..
希望这些可以给购买国茂减速机的用户提供帮助！
I hope these can give the users to help buy Guomao reducer!

标签: 减速机减速机保养

news

news

减速机一些保养的方法和检修方法

关于我们

工业制动器

新闻资讯

产品展示

减速机

服务热线/Service Line